Firmware Information - Quick Links

DHE Communication link bandwidths

There are four communication channels available on the Torrent DHE. The table below shows the available bandwidth for these links and their intended use.

DHE Communication Channels
Channel Bit Rate Command Bandwith (32-bit Words) Video Data Bandwith (18-bit Words) Purpose
Systran 1.0625 GBit/sec 26.5 Meg/sec 26.5 (53 for 16-bit packed pixels) Meg/sec Primary command downlink, Primary data uplink.
Sync In/Out 39.8 Meg/sec 1.0 Meg/sec n/a Inter-DHE communications, commands, synchronization
UART 9600 240 / sec n/a Engineering and maintenance
GIGe Vision Gigabit Ethernet 412.5 K/sec 26.5 Meg/sec (16-bit words). Alternate control downlink and data uplink

LCB Clock Sources and Frequencies

There are several clock sources available from the LCB clock synthesizer hardware (U28). These clocks provide synchronization to specific areas of the Torrent hardware and firmware. The table below lists the clock name, the nominal frequency and their intended application.

Available LCB clock sources
Clock Name Frequency (Mhz) Purpose
OCLK (internal) 106.25 LCB Oscillator used during LCB Initialization and in Master mode.
sync_in_clk (internal) 39.84375 Master clock input when in Slave mode. OCLK is shut down
BCLK (internal) 106.25 (Master) / 39.84375 (Slave) Clock source for the clock synthesizer. OCLK or sync_in_clk
SysClk (internal) 106.25 General logic, Wishbone bus clock
LCLK 106.25 Low jitter clock source for the GTP Transceiver (SFPDP comms)
PCLK 159.375 Memory.
DCLK 79.6875 AFE interface bridge logic.
TCLK 39.84375 AFE ADC data clock
MCLK 39.84375 Sync port communications and synchronization logic

These clocks are derived from U28 (LMK03000) using the following register constants

LMK03000 Programming Scheme for Master DHE (BCLK = 106.25 MHz)
Clock Name Phase detect Freq. (Mhz) VCO Freq. (Mhz) Divide by 'R' Value VCO Divider Value Divide by 'N' Value Clock Divider Value
SysClk 13.28125 1275 8 2 48 6
LCLK 13.28125 1275 8 2 48 6
PCLK 13.28125 1275 8 2 48 4
DCLK 13.28125 1275 8 2 48 8
TCLK 13.28125 1275 8 2 48 16
MCLK 13.28125 1275 8 2 48 16

For DHE Slave operation, where the BCLK frequency is 39.84375 MHz, the value of the Divide by 'R' value changes to 3. All other constants remain the same.

 

Clock Sources for Master sync clock

There are two clock sources available to provide the master OUTSYNC_CLK. The FPGA internally generated source and a source generated directly from the clock synthesizer hardware (U28). These clocks provide synchronization to the slave DHE systems. The table below lists the combinations available by writing to the SyncClkSelect attribute.

SYNC clock sources and routing
Attribute value OUTSYNC_CLK Source FPGA SYNC CLK source Attribute value OUTSYNC_CLK Source FPGA SYNC CLK source
0x0 U28 U28 0x8 Invalid state Invalid state
0x1 FPGA U28 0x9 Invalid state Invalid state
0x2 U28 FPGA 0xA U28 Disabled
0x3 FPGA FPGA 0xB FPGA Disabled
0x4 Disabled U28 0xC Disabled Disabled
0x5 Invalid state Invalid state 0xD Invalid state Invalid state
0x6 Disabled FPGA 0xE Invalid state Invalid state
0x7 Invalid state Invalid state 0xF Invalid state Invalid state

 

RS232 Communication Channel Command Codes

The LCB supports an engineering RS232 communication port for engineering use. The available commands (shown below) are prefixed with the 'plus' (+) character (0x2B) and completed with a 'Line Feed' character (0x0A). The standard format of 9600 Baud, 8 bits, no parity is supported. Upper or lower case characters are recognized. All address and data values must be expressed in hex. Fields must be separated by a space or tab character. Backspace clears the current command (although currently the display looks messy).

Torrent engineering commands for RS232 link
First Field Second Field Third Field Forth Field Command description
+A 16-bit vector (valid range 0x0 through 0xFFFF) Not Used Not used Forces an Asynchronous Command to synchronize the communication channels after reset
+R Module number (valid range 0x01 through 0xFF) Module Address (valid range 0x0 through 0xFFFF) Not used Returns the 32-bit contents of the addressed register (in hex)
+W Module number (valid range 0x01 through 0xFF) Module address (valid range 0x0 through 0xFFFF) 32-bit data value (valid range 0x0 through 0xFFFFFFFF) Writes the 32-bit value to the addressed register
+S 8-bit data value (valid range 0x0 through 0xFF) as sequencer start vector Not used Not used Triggers a 'Start Exposure' event in the sequencer with the 8-bit start vector

 

Firmware Module Addressing and Identity Codes

As per ICD 6.1 we use a board select code in each command sent to the LCB to address the individual modules that make up the firmware suit loaded to the Virtex part. This note pretends to fix the identity of the modules selected by each bit of the board select bit field used in the command structure. There are 10 bits available in this field. Torrent currently supports the use of the lowest order five bits although eight bits can be specified (with minor modification) in the Torrent architecture. The table below identifies the correspondence:

Torrent firmware module addressing
Board Select Bit Module Selected Module Abbreviation Module Identity Code Module purpose
0 (0x01) LCB Control Module LCB 201 Communications and digital control of the Torrent DHE
1 (0x02) Power Supply Services PSM 202 Safety, Control, and telemetry of the power supply board (PSM)
2 (0x04) Configuration Services CFG 203 Configuration data management (eeprom data), LCB clock control and sequencer (CFG)
3 (0x08) Pixel Data Services PIX 204 Pixel data memory and descrambling logic common to OUV and IR (PIX)
4 (0x10) Analog Front End Control (AFE) AFE 205 Analog front end electronics control and pixel acquisition (IR or OUV).
5 (0x20) Spare select bit SPR1 Not assigned Spare module select bit.
6 (0x40) Spare select bit SPR2 Not assigned Spare module select bit.
7 (0x80) Clock Services CLK 208 Clock control module.

 

Standard Data Destination Codes for Communication

The LCB_Control module supplies four duplex channels of communications with the DHE. These four comms channels are: Serial FPTP (Systran Emulation), GIGe (Gigabit ethernet), UART (via serial at 9600 Baud, no handshake), and the SYNC port that links to other slave/master DHE's. The comms destination bits set the required destination for these devices. Setting more than one bit results (mostly !) in parallel transmission to all devices.

Comm Device bit assignments
Bit Number Comm Device
0 ("0001") Serial FPDP
1 ("0010") SYNC Port
2 ("0100") UART Port
3 ("1000") GIGe Port

 

Standard Register Addresses for Firmware Modules

Each firmware module must supply several registers to support the automatic recognition and configuration processes of the PAN computer. These module addresses are shown below with their functional description:

Standard Torrent Module Registers
Address Register Name Write / Read Register purpose
0xFFFF CodeId 32-bit read only Version number of the firmware module code as an integer. Divide by 100 for major / minor version.
0xFFFF RebootCmd 32-bit Write only (data discarded) Write to this register to warm reboot the LCB. All module select bits must be high i.e. 0xFF.
0xFFFE ModuleId 32-bit read only Module identification number of the firmware module - see section on Firmware Module Addressing and Identity Codes
0xFFFE ResetCmd 32-bit Write only (data discarded) Write to this register to reset the module. Multiple module select bits may be specified in the same command. Writing to this location with the all board select bits set high effects a general LCB system reset to all modules and the wishbone bus infrastructure.
0xFFFD Status 32-bit Read only Read of module status word - Data is module specific.

 

Power Supply Status word definition

The power supply monitors the state of the hardware protection circuits on the LCB-MEZ board. These status bits, when true, indicate a hardware protection fault condition that has interrupted the power supply to one or both of the AFE boards. This status regester is (usually) read as an attribute from the DHE at address 0x016F. The attribute name is PwrSupplyStatus.The status bits and their function definitions are shown below :

Power Supply Status Register
Bit Purpose Bit Purpose
7 AFE-1 VANA Power Protection Active 3 AFE-1 / AFE-2 VHV Power Protection Active
6 AFE-1 VCB Power Protection Active 2 Vbb supply active
5 AFE-2 VANA Power Protection Active 1 AFE Power Up Sequence Complete / AFE Power is _ON_
4 AFE-2 VCB Power Protection Active 0 Power Supply Power Up Sequence Complete / Power is Available

 

AFE Mezzanine Override register bit definitions

The mezzanine override register allows you to independently control the AFE power enable bits for the mezzanine board. This is _ONLY_ used for testing purposes since indiscriminate enabling power supplies can cause you to exceed the power supply load capabilities. This register is read and write at address 0x202 in the PSM module

Mezzanine Override Register
Bit Purpose Bit Purpose
7 Not used 3 Not used
6 AFE 2 +/- VHV supply enable 2 AFE 1 +/- VHV supply enable
5 AFE 2 +/- VCB supply enable 1 AFE 1 +/- VCB supply enable
4 AFE 2 +/- VANA supply enable 0 AFE 1 +/- VANA supply enable

 

DheTempSensorSlct Register Value Significance

This register select which temperature sensor in the DHE is to be used for feedback in the DHE temperature servo loop. The selection of the sensor is based upon a 1 Of 8 (3-bit) code set into the DheTempSensorSlct attribute. The codes are :

DheTempSensorSlct Register Significance
Code Selected Temp Sensor
0 ("000") FPGA temperature sensor (default)
1 ("001") LCB_temperature0
2 ("010") LCB_temperature1
3 ("011") AFE1_temperature0
4 ("100") AFE1_temperature1
5 ("101") AFE2_temperature0
6 ("110") AFE2_temperature1
7 ("111") Load feedback from PAN attribute write (for testing purposes)

 

Sequencer State Register Bit Assignments for Firmware Modules

Each firmware module that requires to know the sequencer state information provides a 32-bit register at address 0xFFF0. The sequencer uses this register to periodically write the sequencer state information to all modules that use this address. The lower 16-bits of the register are static values and may be used to indicate the current mode of the sequencer function (e.g. ROI Readout Mode, Digital Averaging Enabled, etc.). The top 16-bits (31:16) are strobe signals that indicate an event during the sequencer operation (Frame Start, Line Start, etc.) and these bits persist for, and are synchronous to one SysClk cycle before being cancelled. The table below indicates the significance of the Sequencer State Register.

Sequencer State Register Assignments
Bit Signal Type Used By Bit Signal Type Used By
31 FrameStartSync Strobe AFE 15 Spare Static n/a
30 LineStartSync Strobe AFE 14 Spare Static n/a
29 Spare Strobe n/a 13 Spare Static n/a
28 Spare Strobe n/a 12 Spare Static n/a
27 Spare Strobe n/a 11 Spare Static n/a
26 Spare Strobe n/a 10 Spare Static n/a
25 Spare Strobe n/a 9 Spare Static n/a
24 Spare Strobe n/a 8 Spare Static n/a
23 Spare Strobe n/a 7 Spare Static n/a
22 Spare Strobe n/a 6 Spare Static n/a
21 Spare Strobe n/a 5 Spare Static n/a
20 Spare Strobe n/a 4 Spare Static n/a
19 Spare Strobe n/a 3 Spare Static n/a
18 Spare Strobe n/a 2 Spare Static n/a
17 Spare Strobe n/a 1 Spare Static n/a
16 Spare Strobe n/a 0 Spare Static n/a

 

Addresses for I2C Bus Devices / FPGA Boot Code Version Selection

There are five I2C buses associated with the Torrent DHE; one I2C bus for every physical board (LCB, PSM, TSM, AFE1, AFE2). There are four devices attached to each bus. This table lists their addresses and describes their use. During the DHE initialization (just after boot), the SDA signal line of each I2C bus is used to detect the presence of the physical board. The SCL signal for AFE1 (AFE_SCL_SRC0) is also used to direct the revision of the code that is booted at power up. This signal is pulled 'high' through a 50K Ohm pullup to 3.3v on the LCB. IR AFE boards should pull this signal low via a 3.3K Ohm resistor to the VPIFC GND return. This will select revision zero of the XF32P eeprom (LCB U43) boot code to load to the FPGA for IR operation. CCD AFE boards should leave this signal floating to select revision 1 of the boot code for VIS operation.

I2C Bus Module Addresses
Address Device Type Description
0x48 MCP9803 Temperature sensor used to control the DHE operating temperature and supply telemetry
0x49 MCP9803 Temperature sensor used to control the DHE operating temperature and supply telemetry
0x50 DS28CM00 48-bit silicon serial number as unique identity for each hardware board. Only the ls 32-bits are read.
0x54 24AA128 Calibration coefficient store space. Page written and read; 256 Pages each with 16 x 32-bit words.

For PAN control of these resources there are several registers that are used to read and write to the I2C devices. These are listed in the following table:

Control of I2C EEProm, Temperature sensors, and Silicon Serial Numbers
Attribute name Address Write Value Read Value Description
DetectI2CBus 0x0012 Anything Bit(4)=AFE2 Detected,
Bit(3)=AFE1 Detected,
Bit(2)=TSM Detected,
Bit(1)=PSM Detected,
Bits(0)=always '1'
5-bit read/write register. Write anything to initiate I2C bus detection, Read to see hardware devices available
ReadI2CBusTemps 0x0013 Bits(20:16)=I2C Channel Addr, Bit(0)=Temperature sensor 1 or 2. Not Accessible 32-bit write register. Write to initiate I2C temperature sensor read cycle and update read only registers.
ReadI2CBusSerial
Numbers
0x0014 Bits(20:16)=I2C Channel Addr. Not Accessible 32-bit write register. Write to initiate I2C silicon serial number reads and update read only registers
eepRdCmdReg 0x0020 Bits(20:16)=I2C Channel Addr. Bits(7:0)=EEProm page address. Bit(31)=I2C manager busy,
Bit(30)= Error occurred during read - bad I2C acknowledge.
32-bit read/write register. Command register to select and read an eeprom page
eepWrtCmdReg 0x0021 Bits(20:16)=I2C Channel Addr. Bits(7:0)=EEProm page address. Bit(31)=I2C manager busy,
Bit(30)= Error occurred during write - bad I2C acknowledge.
32-bit read/write register. Command register to select and write an eeprom page

Channel Address values for the physical hardware boards are: LCB = 1, PSM = 2, TSM = 4, AFE1 = 8, AFE2 = 16.

For the ReadI2CBusTemps, ReadI2CBusSerialNumbers, and eepWrtCmdReg commands, multiple channel addresses are allowed (i.e. you can read multiple temperature sensors or write the same data to multiple EEproms using just one command transaction).

For the eepRdCmdReg command, only one unique channel address is allowed.

 

Bit significance for the LED_1_Slct and LED_2_Slct indicator attributes

There are two 8-bit registers assigned to provide visual indication of the internal signals of the FPGA. These registers are read / write. By setting a bit true the indicator (LED1 or LED2) will flash briefly (25ms) every time the selected signal becomes active true. LED1 is currently mounted on the Sync In port connector and LED2 is mounted on the Sync Out Port connector. The tables below indicate the significance of each attribute bit.

LED1 Signal Select Bits
bit signal
7 BusReset
6 SlaveErrOut(4)
5 SlaveErrOut(3)
4 SlaveErrOut(2)
3 SlaveErrOut(1)
2 SlaveErrOut(0)
1 CfgCycleRequest
0 LcbCycRequest
LED2 Signal Select Bits
bit signal
7 SRC_SYNC_OUT
6 SNK_SYNC_IN
5 V33_SYNC_OUT
4 V300_POLARITY
3 V180_PWR_EN_N
2 V80_PWR_EN_N
1 VFAN_PWR_EN_N
0 MCLK_SEL_N

 

DbgSigSlct attribute values

This attribute controls the selection of a group of eight signals that are presented on the CFGDATA(7:0) signals (connector J4) on the LCB. By setting the attribute to different values, the hardware debug signals are available for diagnostic use. The attribute accepts values from zero to ten. The list below shows the significance.

DbgSigSlct Attribute values
Value Signal Group
0 Signals off
1 LCB Control Signal group
2 PSM Services Signal group
3 CFG Services Signal group
4 PIX Services Signal group
5 AFE Control Signal group
6 Signals off - Future AFE2 Signal group
7 Signals off - Spare
8 CLK Services Signal group
9 System Bus Signal group
10 Auxiliary Signal group

These tables list the individual signals for each group.

DbgSigSlct = 1 - LCB Control signal assignments
bit signal
7 GIGe_PIXEL_CLK
6 GIGe_FVAL
5 GIGe_LVAL
4 GIGe_DVAL
3 PixDataRdy
2 GIGe_BULK0_CLK
1 GIGe_BULK0_RXD
0 LinkUp
DbgSigSlct = 2 - PSM Services signal assignments
bit signal
7 AfePwrIsOn
6 TEMP_2_SNS
5 TEMP_1_SNS
4 LOGIC_SYNC
3 V300_SYNC
2 V180_SYNC
1 V80_SYNC
0 V33_SYNC
DbgSigSlct = 3 - CFG Services signal assignments
bit signal
7 MstrScl
6 MstrSdain
5 MstrSdaOut(2)
4 MstrWrtEn
3 SYNC_DHE
2 SE_OUT
1 SE_READY
0 SYNC_POWER
DbgSigSlct = 4 - PIX Services signal assignments
bit signal
7 MemInitDone
6 DlyClkLocked
5 app_af_wren
4 app_af_cmd(0)
3 app_af_cmd(1)
2 rd_data_valid
1 app_wdf_wre
0 MemoryDataClk
DbgSigSlct = 5 - AFE Control signal assignments
bit signal
7 DacDevData(17)
6 DacDevData(16)
5 AFE_CLKBIAS(77)
4 AFE_CLKBIAS(48)
3 SerialSync(0)
2 SerialData(0)
1 SerialClk(0)
0 DacCtrlDataRdy
DbgSigSlct = 8 - CLK Services signal assignments
bit signal
7 DCLK_FEED
6 BCLK_FEED
5 CLK_CTRL_CS_N
4 CLK_CTRL_GOE
3 CLK_CTRL_LOCK
2 CLK_CTRL_SYNC
1 CLK_CTRL_DATA
0 CLK_CTRL_CLK
DbgSigSlct = 9 - System signal assignments
bit signal
7 Mstr1Grnt
6 Mstr0Grnt
5 SlaveCycle
4 SlaveWrite
3 SlaveError
2 StatusEnable
1 SlaveAck1
0 SlaveAck0

 

Wishbone system status signal assignments for Firmware Modules

Each firmware module can supply eight bits of 'out of band' status information which is used to transport slow signals (such as static configuration values) to other modules. The routing is controlled by the System Intercon module which employs static assignment to route input status bits to the global 32-bit output status sent to the other modules slave interface. The table below shows the routing information for the system at FPGA version level 2.22.

Global Status Assignments
Bit Signal Origin Used By Bit Signal Origin Used By
31 ShutDownQuick PSM AFE 15 n/a n/a Spare
30 AsyncFlag LCB CFG 14 n/a n/a Spare
29 ReadoutInProgress CFG AFE 13 n/a n/a Spare
28 FrameStart CFG AFE 12 n/a n/a Spare
27 LineStart CFG AFE 11 n/a n/a Spare
26 MemPwrEnbld PSM PIX 10 n/a n/a Spare
25 ClocksAreLocked CLK PIX 9 n/a n/a Spare
24 AFEPowerOn PSM AFE 8 StreamMode PIX AFE
23 VHVPolarity PSM AFE 7 DheIsSlave CFG LCB, CLK
22 AFE 2 is enabled AFE PSM 6 Pixels16 PIX LCB
21 AFE 1 is enabled AFE PSM 5 PackedPixels PIX LCB
20 n/a n/a Spare 4 AFE2_Detected CFG PSM, AFE
19 n/a n/a Spare 3 AFE1_Detected CFG PSM, AFE
18 n/a n/a Spare 2 TempChanSlct(2) PSM CFG
17 n/a n/a Spare 1 TempChanSlct(1) PSM CFG
16 n/a n/a Spare 0 TempChanSlct(0) PSM CFG

These next tables show the module status output assignments:

 

 

Local Control Board Module Status Output Assignments

Local Control Board Module (LCB) System Status Output Assignments
Bit Signal Description Bit Signal Description
7 n/a Spare 3 n/a Spare
6 n/a Spare 2 n/a Spare
5 n/a Spare 1 n/a Spare
4 n/a Spare 0 AsyncFlag True after reboot while waiting for a comm port async command
Local Status significance
Bit Signal Description Bit Signal Description
0 AsyncFlag_i Awaiting communication sync command from PAN 7:1 n/a Spares
8 CommDeviceBusy_i The science data comms channel is blocked up 9 SfpdpLossOfSig_i Systran link down. No carrier present signal
10 SfpdpTxFault_i There is a hardware fault in the Systran optical transmitter part 11:12 n/a Spares
28:13 WbErrorStats_i(15:0) Wishbone bus error statistics      

Power Supply Services Module Status Output Assignments

Power Supply Services Module (PSM) System Status Output (0xFFFD) Assignments
Bit Signal Description Bit Signal Description
7 n/a Spare 3 ShutDownQuick Emergency shutdown signal
6 VHVPolarity True indicates N-Channel mode (positive VHV) 2 TempChanSlct(2) 1 of 8 slct of DHE temperature control sensor
5 AFEPowerOn The AFE boards have VANA+/- powered up 1 TempChanSlct(1) 1 of 8 slct of DHE temperature control sensor
4 MemPwrEnbld 1.8v Memory power is available. 0 TempChanSlct(0) 1 of 8 slct of DHE temperature control sensor
PSM Local Status register (0xFFFC) significance
Bit Signal Description Bit Signal Description
0 VFanTempSensorSlct_reg(0) Same signal as system status 1 VFanTempSensorSlct_reg(1) Same signal as system status
2 VFanTempSensorSlct_reg(2) Same signal as system status 3 ShutDownQuick Panic !!
4 TsmPresent_i Indicates that the TSM is present. 5 n/a Spare
6 n/a Spare 7 n/a Spare
PSM Power Status Register (0x020F) significance
Bit Signal Description Bit Signal Description
0 PrimaryPwrStat Primary power is available 1 AfePwrStat AFE power is available
2 VbbEnableFlag Vbb supply is enabled (after safety conditioning) 3 AfeV300Fail Mezzanine Fail indicator for VHV
4 Afe2V180Fail Mezzanine Fail indicator for VCB on AFE2 5 Afe2V80Fail Mezzanine Fail indicator for VANA on AFE2
6 Afe1V180Fail Mezzanine Fail indicator for VCB on AFE1 7 Afe1V80Fail Mezzanine Fail indicator for VANA on AFE1
PSM Mezzanine Override Register (0x0202) significance
Bit Signal Description Bit Signal Description
7:0 MezOverRide_reg As written by PAN 8 Afe1V80Fail Mezzanine Fail indicator for VANA on AFE1
9 Afe1V180Fail Mezzanine Fail indicator for VCB on AFE1 10 AfeV300Fail Mezzanine Fail indicator for VHV
11 n/a Not used 12 Afe2V80Fail Mezzanine Fail indicator for VANA on AFE2
13 Afe2V180Fail Mezzanine Fail indicator for VCB on AFE2 14 AfeV300Fail Repeat of Mezzanine Fail indicator for VHV

Configuration Services Module Status Output Assignments

Configuration Services Module (CFG) System Status Output Assignments
Bit Signal Description Bit Signal Description
7 n/a Spare 3 DheIsSlave The DHE is configured as a slave device in a multi-DHE system
6 n/a Spare 2 AFE2_Detected The AFE2 board is physically present
5 LineStart Indicates a new row beginning 1 AFE1_Detected The AFE1 board is physically present
4 FrameStart Indicates a new frame beginning 0 ReadoutInProgress Sequencer is actively reading detector
Local Status significance
Bit Signal Description Bit Signal Description
0 ReadoutActive Sequencer EFR bit to indicate that ... 1 AFE0_ModuleDetect AFE1 has been detected during the I2C bus search
2 AFE1_ModuleDetect AFE2 has been detected during the I2C bus search 3 DheIsSlave DHE is operating as a slave DHE
4 FrameStart A frame start flag has been issued in the pixel stream 5 LineStart A line start flag has been issued in the pixel stream
15:6 not used Spare 19:16 BusTimeoutReg Sequencer Wishbone master Bus Timeout Register
23:20 BusGrantReg Sequencer Wishbone master Bus Grant error register 27:24 BusErrorReg Sequencer Wishbone master Bus slave Error register
31:28 BusEventStatusReg Sequencer Wishbone master Bus status register      

Pixel Services Module Status Output Assignments

Pixel Services Module (PIX) System Status Output Assignments
Bit Signal Description Bit Signal Description
7 n/a Spare 3 n/a Spare
6 n/a Spare 2 StreamMode Pixel data path configured for Stream Data acquisition mode i.e. no memory buffering
5 n/a Spare 1 Pixels16 Pixel data has been scaled to 16-bits by the PIX module.
4 n/a Spare 0 PackedPixels Each 32-bit pixel data word contains 2 x 16-bit pixels.
Local Status significance
Bit Signal Description Bit Signal Description
0 MemCntrInitDone_i Memory system calibrated and ready for use 31:1 n/a Spares

 

Analog Front End Control Module Status Output Assignments

System Status Output Assignments
Bit Signal Description Bit Signal Description
7 n/a Spare 3 n/a Spare
6 n/a Spare 2 n/a Spare
5 n/a Spare 1 afe_enbl_reg(1) True when AFE 2 is enabled via AfeInterfaceEnbl
4 n/a Spare 0 afe_enbl_reg(0) True when AFE 1 is enabled via AfeInterfaceEnbl
Local Status significance
Bit Signal Description Bit Signal Description
0 RfshTpActFlag Test points are being refreshed 1 RfshActiveFlag DAC and Test Points are being refreshed
4 tp_fifo_empty The Test point write FIFO is empty 5 dac_fifo_empty The DAC write FIFO is empty
8 TelScanGo Telemetry scan is active 9 RfshTpWrtFifo transfer test point index to tp write fifo

Clock Services Module Status Output Assignments

Clock Services Module (CLK) System Status Output Assignments
Bit Signal Description Bit Signal Description
7 n/a Spare 3 n/a Spare
6 n/a Spare 2 n/a Spare
5 n/a Spare 1 n/a Spare
4 n/a Spare 0 ClocksAreLocked Clock Synthesizer has lock and clocks are good
Local Status significance
Bit Signal Description Bit Signal Description
0 LockDetect_i The clock generator is running locked to the reference frequency 31:1 n/a Spares

Updated on May 6, 2021, 7:55 pm